The learner will identify tools and practices associated with setting up a lathe to turn between centers.
Turning Between Centers
_________________ are often the first steps taken in getting ready to turn between centers.
Question 1 of 10
Turning Between Centers
Correct!
_________________ are often the first steps taken in getting ready to turn between centers.
Correct Answer
Facing and center drilling
Question 1 of 10
Turning Between Centers
Incorrect
_________________ are often the first steps taken in getting ready to turn between centers.
Your Answer
Correct Answer
Facing and center drilling
Question 1 of 10
Turning Between Centers
Center drills break as a result of ______.
Question 1 of 10
Turning Between Centers
Correct!
Center drills break as a result of ______.
Correct Answer
too heavy a feed, too low speed, and tailstock out of alignment
Question 1 of 10
Turning Between Centers
Incorrect
Center drills break as a result of ______.
Your Answer
Correct Answer
too heavy a feed, too low speed, and tailstock out of alignment
Question 1 of 10
Turning Between Centers
In what kind of chuck is a square or rectangular workpiece set up for center drilling?
Question 1 of 10
Turning Between Centers
Correct!
In what kind of chuck is a square or rectangular workpiece set up for center drilling?
Correct Answer
4-jaw independent
Question 1 of 10
Turning Between Centers
Incorrect
In what kind of chuck is a square or rectangular workpiece set up for center drilling?
Your Answer
Correct Answer
4-jaw independent
Question 1 of 10
Turning Between Centers
When taking a facing cut on a workpiece, the point of the tool should _____.
Question 1 of 10
Turning Between Centers
Correct!
When taking a facing cut on a workpiece, the point of the tool should _____.
Correct Answer
be right on center
Question 1 of 10
Turning Between Centers
Incorrect
When taking a facing cut on a workpiece, the point of the tool should _____.
Your Answer
Correct Answer
be right on center
Question 1 of 10
Turning Between Centers
To correctly face from the outside into center using a standard right-hand, high-speed steel tool holder, ______.
Question 1 of 10
Turning Between Centers
Correct!
To correctly face from the outside into center using a standard right-hand, high-speed steel tool holder, ______.
Correct Answer
a left-hand tool would be used
Question 1 of 10
Turning Between Centers
Incorrect
To correctly face from the outside into center using a standard right-hand, high-speed steel tool holder, ______.
Your Answer
Correct Answer
a left-hand tool would be used
Question 1 of 10
Turning Between Centers
When taking facing cuts, ______.
Question 1 of 10
Turning Between Centers
Question 1 of 10
Turning Between Centers
Incorrect
When taking facing cuts, ______.
Your Answer
Correct Answer
the carriage must be locked
Question 1 of 10
Turning Between Centers
If a long workpiece needs to be faced while being held between centers, a ______ would be used.
Question 1 of 10
Turning Between Centers
Correct!
If a long workpiece needs to be faced while being held between centers, a ______ would be used.
Correct Answer
half center
Question 1 of 10
Turning Between Centers
Incorrect
If a long workpiece needs to be faced while being held between centers, a ______ would be used.
Your Answer
Correct Answer
half center
Question 1 of 10
Turning Between Centers
The greater the size of the work to be held between centers and the heavier the cuts, ______.
Question 1 of 10
Turning Between Centers
Correct!
The greater the size of the work to be held between centers and the heavier the cuts, ______.
Correct Answer
the larger the center-drilled hole
Question 1 of 10
Turning Between Centers
Incorrect
The greater the size of the work to be held between centers and the heavier the cuts, ______.
Your Answer
Correct Answer
the larger the center-drilled hole
Question 1 of 10
Turning Between Centers
Center-drilled holes that are drilled too deeply will cause _____.
Question 1 of 10
Turning Between Centers
Correct!
Center-drilled holes that are drilled too deeply will cause _____.
Correct Answer
the headstock and tailstock centers to fit improperly
Question 1 of 10
Turning Between Centers
Incorrect
Center-drilled holes that are drilled too deeply will cause _____.
Your Answer
Correct Answer
the headstock and tailstock centers to fit improperly
Question 1 of 10
Turning Between Centers
The advantage of working between centers is ______.
Question 1 of 10
Turning Between Centers
Correct!
The advantage of working between centers is ______.
Correct Answer
diameters can be turned concentrically
Question 1 of 10
Turning Between Centers
Incorrect
The advantage of working between centers is ______.
Your Answer
Correct Answer
diameters can be turned concentrically
Question 1 of 10
Turning Between Centers
Question 1 of 10
Turning Between Centers
Question 1 of 10
Turning Between Centers
Incorrect
Identify the lathe accessory shown.
Your Answer
Correct Answer
Ball bearing center
Question 1 of 10
Turning Between Centers
Question 1 of 10
Turning Between Centers
Correct!
Identify the lathe accessory shown.
Correct Answer
Live center or dead center
When a dead center is in the headstock, it is known as a live center.
Question 1 of 10
Turning Between Centers
Incorrect
Identify the lathe accessory shown.
Your Answer
Correct Answer
Live center or dead center
When a dead center is in the headstock, it is known as a live center.
Question 1 of 10
Turning Between Centers
Question 1 of 10
Turning Between Centers
Question 1 of 10
Turning Between Centers
Question 1 of 10
Turning Between Centers
Score
You have answered 5 of 10 questions correctly.
50%
See other flashcards and apps related to:
Question 1 of 10
No Comments Yet
Turning Between Centers by Fox Valley Technical College is licensed under a Creative Commons Attribution 3.0 Unported License.