The learner will identify turning tool materials and the cutting conditions associated with turning.

Turning Tool Fundamentals

In an internal grooving operation where the tool is feed out toward the outside of the workpiece, you want the spindle RPM to:

Question 1 of 10

Turning Tool Fundamentals

Correct!

In an internal grooving operation where the tool is feed out toward the outside of the workpiece, you want the spindle RPM to:

Correct Answer

Decrease

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Incorrect

In an internal grooving operation where the tool is feed out toward the outside of the workpiece, you want the spindle RPM to:

Your Answer

Correct Answer

Decrease

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Sparking in the cutting zone during a turning operation is usually evidence of _______ wear.

Question 1 of 10

Turning Tool Fundamentals

Correct!

Sparking in the cutting zone during a turning operation is usually evidence of _______ wear.

Correct Answer

Abrasion

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Incorrect

Sparking in the cutting zone during a turning operation is usually evidence of _______ wear.

Your Answer

Correct Answer

Abrasion

 Next Question
Question 1 of 10

Turning Tool Fundamentals

In a facing operation where the tool is feed in toward the center of the workpiece, the cutting speed will ______ continually if the spindle RPM is at a fixed RPM.

Question 1 of 10

Turning Tool Fundamentals

Correct!

In a facing operation where the tool is feed in toward the center of the workpiece, the cutting speed will ______ continually if the spindle RPM is at a fixed RPM.

Correct Answer

Decrease

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Incorrect

In a facing operation where the tool is feed in toward the center of the workpiece, the cutting speed will ______ continually if the spindle RPM is at a fixed RPM.

Your Answer

Correct Answer

Decrease

 Next Question
Question 1 of 10

Turning Tool Fundamentals

In the chip-forming process, which material is likely to form a discontinuous chip?

Question 1 of 10

Turning Tool Fundamentals

Correct!

In the chip-forming process, which material is likely to form a discontinuous chip?

Correct Answer

Cast iron

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Incorrect

In the chip-forming process, which material is likely to form a discontinuous chip?

Your Answer

Correct Answer

Cast iron

 Next Question
Question 1 of 10

Turning Tool Fundamentals

The greatest drawback to brazed carbide tooling is:

Question 1 of 10

Turning Tool Fundamentals

Correct!

The greatest drawback to brazed carbide tooling is:

Correct Answer

The re-sharpening expertise that is required

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Incorrect

The greatest drawback to brazed carbide tooling is:

Your Answer

Correct Answer

The re-sharpening expertise that is required

 Next Question
Question 1 of 10

Turning Tool Fundamentals

The amount of plastic deformation that the metal goes through during the metal cutting process depends considerably on the:
Question 1 of 10

Turning Tool Fundamentals

Correct!

The amount of plastic deformation that the metal goes through during the metal cutting process depends considerably on the:

Correct Answer

Rake angle

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Incorrect

The amount of plastic deformation that the metal goes through during the metal cutting process depends considerably on the:

Your Answer

Correct Answer

Rake angle

 Next Question
Question 1 of 10

Turning Tool Fundamentals

The feed rate in turning is typically measured in:

Question 1 of 10

Turning Tool Fundamentals

Correct!

The feed rate in turning is typically measured in:

Correct Answer

FPR

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Incorrect

The feed rate in turning is typically measured in:

Your Answer

Correct Answer

FPR

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Plastic deformation occurs:
Question 1 of 10

Turning Tool Fundamentals

Correct!

Plastic deformation occurs:

Correct Answer

At high temperatures in the cutting zone

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Incorrect

Plastic deformation occurs:

Your Answer

Correct Answer

At high temperatures in the cutting zone

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Diffusion wear is a product of:

Question 1 of 10

Turning Tool Fundamentals

Correct!

Diffusion wear is a product of:

Correct Answer

Chemical load

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Incorrect

Diffusion wear is a product of:

Your Answer

Correct Answer

Chemical load

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Adhesion wear occurs:

Question 1 of 10

Turning Tool Fundamentals

Correct!

Adhesion wear occurs:

Correct Answer

At low temperatures in the cutting zone

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Incorrect

Adhesion wear occurs:

Your Answer

Correct Answer

At low temperatures in the cutting zone

 Next Question
Question 1 of 10

Turning Tool Fundamentals

One of the greatest differences between a manual lathe and a CNC lathe is:
Question 1 of 10

Turning Tool Fundamentals

Correct!

One of the greatest differences between a manual lathe and a CNC lathe is:

Correct Answer

Number of tools that can be mounted

 Next Question
Question 1 of 10

Turning Tool Fundamentals

Incorrect

One of the greatest differences between a manual lathe and a CNC lathe is:

Your Answer

Correct Answer

Number of tools that can be mounted

 Next Question
Question 1 of 10

Turning Tool Fundamentals

When we measure the speed on the workpiece at the cutting point, it is known as:

Question 1 of 10

Turning Tool Fundamentals

Correct!

When we measure the speed on the workpiece at the cutting point, it is known as:

Correct Answer

Cutting speed

 Finish
Question 1 of 10

Turning Tool Fundamentals

Incorrect

When we measure the speed on the workpiece at the cutting point, it is known as:

Your Answer

Correct Answer

Cutting speed

 Finish
Question 1 of 10
Turning Tool Fundamentals

Score

You have answered 5 of 10 questions correctly.

50%

Start Over

See other flashcards and apps related to:

Question 1 of 10
Author
Published
1/5/2015
Last Updated
1/5/2015
Tags

No Comments Yet

Creative Commons License
Turning Tool Fundamentals by Fox Valley Technical College is licensed under a Creative Commons Attribution 3.0 Unported License.